Zenoah G2500 OPS Manuale del Proprietario

GB-1G2500/G2500 OPSG2500G2500 OPS(One-Push-Start)GBOWNER’S MANUALCHAIN SAWOriginal Language115 59 93-38 (306)01-G2500･G2500 ops_GB_306＿四.indd 1 13.7

GB-10G2500/G2500 OPS7. Fuel and Chain Oil Fuel WARNING• Gasoline is very flammable. Avoid smo king or bringing any flame or sparks near fuel. Make su

GB-11G2500/G2500 OPSGB8. Operating the EngineNOTEWhen restarting immediately after stopping the engine, settheChokeknobintherst-stageposition

GB-12G2500/G2500 OPS2. Put the machine body on the stable ground and make sure that there is no obstacle around the saw-cross-ing portion. Then, whi

GB-13G2500/G2500 OPSGB ADJUSTING THE CARBURETORL needleH needleIdle adjustingscrewThecarburetoronyourunithasbeenfactoryadjusted,butmayrequ

GB-14G2500/G2500 OPS9. SawingWARNING• Before proceeding to yourjob, read the section “For Safe Operation”. It is recommend-ed to first practic

GB-15G2500/G2500 OPSGBA log lying on the ground Saw down halfway, then roll the log over and cut from the opposite side. A log hanging off the ground

GB-16G2500/G2500 OPS2. Fuel filter (a)Usinga wirehook,take outthelterfromthellerport. Fuel filter(b)Washthelterwithgasoline. Repl

GB-17G2500/G2500 OPSGB11. Maintenance of Saw Chain and Guide BarWARNINGBe sure to round off the front edge to reduce the chance of kickback or tie-str

GB-18G2500/G2500 OPS12. Troubleshooting GuideCase 1. Starting failure WARNING•Make sure the icing prevention system is not working.Case 2. Lack of

GB-19G2500/G2500 OPSGBLimited warrantyShould any failure occur on the product under normal operating conditions within the applicable warranty pe

GB-2G2500/G2500 OPS⑧⑦④③⑫⑬①②⑤⑥⑨⑩⑪1. Parts locationContents 1. Parts location ...2 2. Specication .

01-G2500･G2500 ops_GB_306＿四.indd 20 13.7.4 5:43:58 PM

GB-3G2500/G2500 OPSGBPower unit:G2500/G2500 OPSDisplacement (cm3): ... 25.4Fuel: ...Mixture (

GB-4G2500/G2500 OPS4. For safe operationWARNINGThis chainsaw has been especially designed for tree maintenance and should therefore only be use

GB-5G2500/G2500 OPSGB(1)muferguard(2) guide bar(3) saw chain20. Operate the chain saw only in well ventilated areas. Never start or run t

GB-6G2500/G2500 OPSWORKING WITH TREE SERVICE CHAIN-SAWS FROM A ROPE AND HARNESSThis chapter sets out working practices to reduce the riskofinjur

GB-7G2500/G2500 OPSGBGaining a good footing at the working position can be assisted by use of a temporary foot stirrup created from an endless sling.S

GB-8G2500/G2500 OPS5. Explanation of Symbols on the Machine• Forsafeoperationandmaintenance,symbolsarecarvedinreliefonthemachine. Accor

GB-9G2500/G2500 OPSGB6. Installing Guide Bar and Saw ChainA standard saw unit package contains the items as illustrated. 5. Fit the chain tensioner n